MY double D contd..
DAY 2
9:38 AM 6/27/2008 >
yesterday the following were purchased
-Capacitor box , all the reqd pf s , it was lacking some of the reqd values
soo i added the values ..
still some are missing line 47kpf etc ,plan to purchase today ...
-IC CD 4049 , L -FETs j112 [as a replace ment for the J109 ] ,vendor told it should match the
actual one upto 90%
-Ribbon wire 6 core , 1 mtr , for the pots ,
-Mic jack and socket , for testing phase i am using a cheap mic jack 10 Rs and Mic socket :)
-Electorlytics 10uf and 4.7uf ,diodes 1N4007 [for the soldering iron ..heh not part of original double d]
-A cutter and Stripper , to be used wire and leg cutter
-A soap box ...wait its a temporary cabinet to hold the SIX POTS ,and the mic jack ..battery etc what so-ever
- also a thin soap box is . easy to drill ... with the mosquito coils ..my new trick
The already exiting parts
- resistor box , still some missing values like 1 M , 2.2 M , 220K etc
soo i have to add today
-solder materials
-hook up wire , wires with one solid strand
-favicol, see below
-Added the components to the board [yellow verro board for a test run]
The disaster ..
My cheap [25 rs] soldering iron died !
- so i i just the componets are added to the verro board as per the plan in the website ,
This saves time !
- and i used *favicol* to hold them in place as i could not solder the components
[usually after the legs are bent and shortened they tend to fall out and if it happens will be a bigg trouble ]
-finally i was able to visualize how the assembled circuit will look after it is done
to do:
-Buy a good soldering iron , missing parts ,extra solder wires , shielded wires
-then the solder the board
-solder the ribbons to the pots ,fot in the soap box
-test by connecting to the pocket AMP
(...my secret tiny amp ..runs on 9V battery )
-Add a killer looking final cabinet ..keep watching
9:38 AM 6/27/2008 >
yesterday the following were purchased
-Capacitor box , all the reqd pf s , it was lacking some of the reqd values
soo i added the values ..
still some are missing line 47kpf etc ,plan to purchase today ...
-IC CD 4049 , L -FETs j112 [as a replace ment for the J109 ] ,vendor told it should match the
actual one upto 90%
-Ribbon wire 6 core , 1 mtr , for the pots ,
-Mic jack and socket , for testing phase i am using a cheap mic jack 10 Rs and Mic socket :)
-Electorlytics 10uf and 4.7uf ,diodes 1N4007 [for the soldering iron ..heh not part of original double d]
-A cutter and Stripper , to be used wire and leg cutter
-A soap box ...wait its a temporary cabinet to hold the SIX POTS ,and the mic jack ..battery etc what so-ever
- also a thin soap box is . easy to drill ... with the mosquito coils ..my new trick
The already exiting parts
- resistor box , still some missing values like 1 M , 2.2 M , 220K etc
soo i have to add today
-solder materials
-hook up wire , wires with one solid strand
-favicol, see below
-Added the components to the board [yellow verro board for a test run]
The disaster ..
My cheap [25 rs] soldering iron died !
- so i i just the componets are added to the verro board as per the plan in the website ,
This saves time !
- and i used *favicol* to hold them in place as i could not solder the components
[usually after the legs are bent and shortened they tend to fall out and if it happens will be a bigg trouble ]
-finally i was able to visualize how the assembled circuit will look after it is done
to do:
-Buy a good soldering iron , missing parts ,extra solder wires , shielded wires
-then the solder the board
-solder the ribbons to the pots ,fot in the soap box
-test by connecting to the pocket AMP
(...my secret tiny amp ..runs on 9V battery )
-Add a killer looking final cabinet ..keep watching
Comments
Post a Comment